The HaspX utilityextracts the update code from the file.ģ. In the HaspX dialog box, choose Update code to open the code file that you received.
Note: Keep a record of the serial number in the event that you need to contact your Reseller or TechnicalSupport at CNC Software.Ģ. The HaspX utility analyzes the license and displays the serial number and supportedMastercamproducts.Verify that the displayed serial number matches the serial number provided with your Mastercam2019 soft-ware kit. L Use Windows Explorer to navigate to the Mastercam2019 installation location, and double-clickHaspX.exe. L (Windows 10) From the Windows desktop, choose Start,Mastercam 2019, Hasp X. L (Windows 7 and 8) From the Windows desktop, choose Start, All Programs,Mastercam 2019, Util-ities, Hasp X. The method you choose is based on your version ofMicrosoft Windows, the update code format, and your preference. Choose one of the followingmethods to run HaspX.exe. To update the codemanually, perform the following procedure.ġ. You can enter a HASP code automatically by double-clicking the update code file (*.HCODE). Updates over a remote con-nection will fail. See instructions for "Updating NetHASP Codes" on page27 and for "Update Codes for Software Licenses" onpage8.ĬAUTION: Before this phase of the update process, youmust have Mastercam installed.Youmust com-plete the following procedure on the computer to which the HASP is attached. Do not force it into the port as youmaydamage the port and the HASP. Locate an available USB port on the computer.ĬAUTION: The HASP attaches to your port in only one orientation. Updates over a remote connection will fail.ġ. Youmust complete the following procedure prior to updating theHASP code.
Follow the procedure below to install licensing hard-ware (also known as aHASP) for a single user. Mastercam supports both single-user and network licensing. Note: Remove all other licensing hardware before entering the Mastercamupdate code. The Mastercam installation pro-gramassociates these file extensions with the program that you use to update the SIM codes.įile Extension License Type Update Program Update code files have a file extension that indicates the type of license they update. L If you receive your update code via post or as part of an installation kit, insert the receivedmedia inthe appropriate drive to access the file. L If you receive your update code via email, save the file attachment to an accessible location. L Included with your Mastercam2019 software kitĬontact your localMastercamReseller if you cannot locate your update code. The update code for a HASP or aNetHASP is a file that is delivered to you by one of these methods: Youmust activate your licensing hardware with this update code beforeyou can run the newor updated version of Mastercam.
You need to do this when you install or upgrade to a new release of Mastercam, andif you are not onMastercamMaintenance. Update Codes for Licensing HardwareUpdate your Mastercam licensing hardware (HASP or NetHASP) with an update code obtained from your Reseller orMastercamCustomer Service. Mastercamhassupported the limited distribution of software licensing via CodeMeter since X7. These licenses eliminate the need for a physical device connected to a computer. The device could either be a local HASP or aNetHASP located on a corporate network.Īs of the release of Mastercam2019, software licenses (also referred to as CodeMeter licenses) are now availableas retail licenses. Historically, this license has been stored in a phys-ical USB plug-in device. License TypesMastercam is a protected software, and requires a license to run. Instructions for updating NetHASP codes are located in "Updating NetHASP Codes"on page27.
This chapter describes how to update Mastercam license codes (SIMs) on HASPs and software license codes, as wellas your version of Mastercam. Use this administrator'sguide to learn about updating license codes, startingMastercam2019 withMastercam Launcher or command-lineswitches, and administering an installation over a network. This administrator's guide covers installation and configuration of networked scenarios. Network Administration (Software Licenses) 32 MastercamAdvanced Configuration Utility 21 SettingMastercam shortcut command-line switches 17 Information displayed in the dialog box 14 To download and install Mastercamupdates 12 A ReadMe file (ReadMe.PDF) installed with each release includes the latest information about Mastercam features and enhancements. The latest version of the doc-ument is installed withMastercamor can be obtained from your local Reseller. The MastercamEnd User LicenseAgreement can be found at:īe sure you have the latest information!Informationmight have changed or been added since this document was published. Terms of UseUse of this document is subject to the MastercamEnd User License Agreement. All rights reserved.Software: Mastercam2019